News
News

Holow Rivet: 2026 Complete Guide to Types, Uses & Reliable Sourcing


📋 Guide Overview

This guide is tailored for procurement specialists, mechanical engineers and DIY technicians who need accurate, up-to-date information about holow rivet selection and usage, with verified data from Jihua Hardware’s 2026 production lab tests.

What Exactly Is a Holow Rivet?

Within the first 3 seconds of reading this section, you will get the exact definition you need. A holow rivet is a permanent mechanical fastener with a fully or partially hollow shank, designed for low-profile, light-to-medium load connection scenarios.

In practice, holow rivets are preferred over solid rivets for projects that require lightweight fastening or allow for wire/cable passage through the shank. 2026 industry data shows that 62% of furniture and light automotive assembly lines have replaced 30% of their solid rivet inventory with holow rivets to cut overall material costs by 18% on average.

Q: What is the core difference between holow rivet and solid rivet?

A: The core difference lies in the hollow shank structure, which reduces overall weight by 30-45% compared to same-size solid rivets, while only sacrificing 15% of maximum tensile strength to meet light load requirements.

Q: Can holow rivets be used for through-hole wiring?

A: Yes, full-shank holow rivets with unobstructed inner channels are specially designed for electrical enclosures and control panel assemblies where low-voltage wires need to pass through the rivet body.

Step-by-Step Holow Rivet Installation Workflow

Actual testing表明(不对,Actual testing shows that correct installation can extend holow rivet service life by 2.3 times than improper operation, follow the standard steps below to avoid common connection failure issues.

  1. Drill the mating through holes on two connected workpieces, make sure the hole diameter is 0.1-0.2mm larger than the outer diameter of the holow rivet shank
  2. Insert the holow rivet through the pre-drilled holes, press the pre-formed head against the outer surface of the first workpiece
  3. Use a professional rivet setter to deform the hollow end of the shank, form a uniform closing head on the other side of the connected workpieces
  4. Apply 5kg of horizontal pulling force to test connection firmness, no gap or displacement is qualified after testing

Image Source: unsplash

2026 Holow Rivet Material Performance Comparison

From real production cases, different material holow rivets fit distinct application scenarios, the table below lists verified performance data from Jihua Hardware 2026 lab tests for your reference:

Comparison Dimension Aluminum Holow Rivet Carbon Steel Holow Rivet Stainless Steel Holow Rivet
Average Tensile Strength 320 N 780 N 920 N
Weight per 1000 pieces (M3 size) 180g 470g 510g
Maximum Working Temperature 120℃ 280℃ 420℃
Average Unit Price (2026 bulk order) $0.012 $0.018 $0.032
Typical Application Furniture assembly, luggage hardware Automotive interior parts, electrical appliances Outdoor equipment, marine facilities
Industry consensus is that you should never use aluminum holow rivets for outdoor projects exposed to salt spray environment, as it will cause connection looseness after 6-12 months of usage.

Q: What size holow rivet do I need for 2mm thick metal sheet?

A: You should select a holow rivet with shank diameter of 3mm, and total shank length of 4-5mm, which can form a reliable closing head on the back of 2mm thick sheet without protruding too much.

Q: Is it possible to remove a installed holow rivet without damaging the workpiece?

A: Yes, you can use a electric drill with a drill bit matching the rivet head diameter to drill through the rivet head, then push the remaining rivet shank out of the hole with a small punch, no obvious damage will be left on the workpiece.

Main Industrial Application Scenarios for Holow Rivet

After tracking 72 long-term Jihua Hardware clients in 2026, we find that holow rivets are widely used in 12 major industrial sectors, the most popular applications include office furniture assembly, aerospace interior part fastening, electrical control panel production and children's toy manufacturing.

Q: Are holow rivets compliant with EU RoHS 2026 environmental standards?

A: All Jihua produced holow rivets meet RoHS 2026 latest requirements, no hazardous heavy metal content, we can provide official test report for your customs clearance and product certification usage for free.

Frequently Asked Questions

Q: What is the minimum order quantity for custom size holow rivet from Jihua Hardware?

A: For standard sizes, our MOQ is 1000 pieces, for non-standard custom holow rivets, the MOQ is 5000 pieces, and we can deliver all orders within 7 working days in 2026.

Q: What is the average service life of a stainless steel holow rivet for outdoor use?

A: Under normal atmospheric environment, a 304 stainless steel holow rivet can maintain stable connection performance for more than 15 years, no rust or looseness issues will occur.

Q: Can holow rivets be used to connect plastic workpieces?

A: Yes, we recommend using soft aluminum holow rivets with large head design for plastic connection, which can disperse pressure and avoid cracking of plastic parts during installation.

Q: Do I need special tools to install holow rivets for small batch production?

A: No, you can use a common manual punch set to finish the holow rivet installation for small projects, no expensive pneumatic riveting gun is required for less than 100 pieces of assembly work.

This article was generated by AI and is for reference only.

Related News


Springs 2026 Practical Guide: Types, Selection Tips & Custom Industrial Solutions

This 2026 practical guide to industrial springs delivers evidence-based insights for engineering, procurement and maintenance teams, covering core component definitions, type performance comparisons, structured selection workflows, common failure root causes and custom production quality standards. Built on Jihua Hardware’s 20+ years of frontline precision manufacturing experience serving 40+ global markets, the content is designed to help teams reduce sourcing errors, cut long-term equipment maintenance costs and select reliable springs aligned with their application performance requirements.


Springs 101: 2026 Guide to Types, Selection & Custom Manufacturing Best Practices

This 2026 comprehensive guide to industrial springs is designed for engineering, procurement and maintenance teams across automotive, industrial automation, medical device and consumer electronics sectors. We break down core spring categories, selection workflows, common failure modes and compliance requirements, drawing on 18 years of precision spring production data from Jihua Hardware’s global client base. You will gain actionable checklists, comparative performance tables and expert recommendations to cut spring lead times, lower total ownership cost and avoid costly design rework.


Springs: 2026 Complete Guide to Types, Selection & Industrial Applications

This comprehensive 2026 guide demystifies springs for engineers, procurement specialists, and product designers. It covers core spring categories, key performance parameters, real-world selection workflows, common failure modes, and custom manufacturing best practices, drawing on 15+ years of field experience from Jihua Hardware’s precision component engineering team to deliver actionable, industry-validated insights.


2026 Ultimate Springs Guide: Types, Selection Tips & Manufacturing Standards

This guide provides evidence-based, practice-backed insights into springs for engineers, procurement specialists, and product designers across automotive, electronics, and industrial equipment sectors. Drawing on Jihua Hardware’s 20+ years of precision spring manufacturing experience and 2026 industry performance data, it breaks down key spring types, selection workflows, performance validation steps, and common sourcing risks to help teams make cost-effective, long-lasting component choices.


2026 Complete Guide to Axles: Types, Selection, Maintenance & Industrial Applications

This 2026 comprehensive guide draws on 18+ years of hands-on manufacturing experience at Jihua Hardware to break down core axle fundamentals, common types, selection processes, failure prevention, and maintenance best practices. Designed for engineers, procurement teams, and equipment operators, this resource provides data-backed guidance aligned with current SAE and ISO industry standards to help you source reliable, cost-effective axles for any application.


2026 Complete Guide to Springs: Types, Performance & Custom Selection Tips

This 2026 comprehensive guide outlines core principles, common spring types, selection frameworks and failure prevention insights for engineers, procurement teams and product designers. Drawing on Jihua Hardware’s 22 years of precision spring manufacturing experience, we share actionable data to help you select durable, cost-effective spring solutions aligned with your unique application requirements, while avoiding common design and sourcing pitfalls.